Mellerware Iron 23805 User Manual

E X E C U T I V E  
B r a v i s s i m o 2 S S t e a m S t a t i o n I r o n  
Model:  
2 3 8 0 5  
2100W  
PLEASE READ ALL INSTRUCTIONS BEFORE USE  
2 y e a r g u a r a n t e e  
 
MW_EX233805 StteamStation_IM.indd  
1
7/25/2007 2:02:50 PM  
Steam ironing  
-
Set the desired temperature with the  
thermostat control (J), depending on the type  
of cloth to be ironed (Fig. 3).  
When you start to iron, proceed as follows:  
-
Unscrew the cap (F) and fill the boiler with  
water, using a jug (Fig. 1) (if you fill it with  
hot water, the appliance will be ready for use  
sooner).  
Fig. 3  
-
The appliance will be ready for use when the  
pressure indicator LED (E) lights up (Fig. 4).  
While ironing, this LED (E) goes on and off  
automatically, this is normal.  
Fig. 1  
-
-
Even if the boiler has a certain level of water, it  
is always recommended to fill it to the top for a  
longer range, thanks to its large 1l capacity.  
Carefully close the cap (F), screwing it to the  
end.  
-
-
-
Place the boiler on a flat , stable surface.  
Plug the appliance into the mains.  
Switch on the boiler and the iron by pressing  
the relevant switches (B) and (A). The  
corresponding LEDs will light (Fig. 2).  
Fig. 4  
-
By pressing the steam switch (H) you will get  
a constant steam jet (Fig. 5). The steam stops  
when you release the switch.  
Fig. 2  
Thermostat Control Fabric Type  
Position  
Steam  
Nylon, Silk  
Wool  
No  
No  
Yes  
••  
•••  
Cotton, Linen  
Fig. 5  
It is recommended not to use steam in the • and  
•• thermostat positions, as water could drip.  
 
MW_EX233805 StteamStation_IM.indd  
4
7/25/2007 2:02:51 PM  
-
-
Clean the base of the iron while it is still hot,  
using a damp cloth, after each use.  
How to fill the boiler while ironing  
To fill the boiler, proceed as follows:  
The rest of the appliance can also be cleaned  
using a damp cloth. Never submerge the  
appliance in water or any other liquid, or hold  
it under a running tap. Do not use solvents or  
abrasive products to clean it.  
-
Eliminate steam pressure from inside the boiler  
by switching on the steam switch (H) (Fig. 5).  
Turn off the boiler (B) and iron (A) switches.  
Unplug the appliance from the mains.  
Carefully unscrew the cap (F) to let the residual  
steam out of the boiler.  
-
-
-
Care and Cleaning  
-
-
Wait for some minutes and carefully pour 1l of  
water into the boiler using a jug (Fig. 1).  
Carefully close the cap (F) again, screwing it to  
the end.  
Before cleaning the iron, ensure it is  
disconnected from the power supply and has  
completely cooled down.  
Deposits and other residues on the soleplate  
can be removed with a rough cloth soaked in a  
vinegar/water solution, or methylated spirits.  
The housing/body may be wiped with a damp  
cloth and then polished with a dry one.  
Dot not use abrasives on the soleplate.  
Keep the soleplate smooth: avoid hard contact  
with metal objects.  
Vertical ironing  
It is possible to iron hanging curtains, garments  
on their own hangers... (Fig. 6)  
NOTE: Ironing dirty fabric or fabric not rinsed  
fully will result in the iron sticking and dirt  
accumulating on the bottom of the soleplate, as  
will a iron set at too high a temperature for the  
relevant fabric.  
Fig. 6  
-
-
Adjust the iron thermostat control (J) to the  
maximum temperature.  
Iron from top to bottom and press the iron  
steam switch (H).  
Important: For cotton and linen clothes, it is  
recommended to put the base of the iron  
in contact with the fabric. For more delicate  
fabrics, it is recommended to keep the base of  
the iron at a distance of some centimetres.  
Dry ironing  
-
-
-
Connect the professional iron to the mains.  
Turn on the iron switch (A).  
Set the iron temperature with the thermostat  
control (J), depending on the fabric to be  
ironed.  
After each ironing  
-
Switch off the professional iron by pressing  
switches (B) and (A).  
-
Unplug the network connection cable (G) from  
the mains.  
 
MW_EX233805 StteamStation_IM.indd  
5
7/25/2007 2:02:51 PM  
Trouble Shooting Guide  
Problem  
Reason  
Action  
Water drips from the holes  
on the base of the iron when  
turning on the steam switch  
(H).  
Iron thermostat control (J) is  
set to the minimum position  
• / ••  
Set the thermostat control to  
the steam zone •••  
The boiler is too full.  
Remove some water.  
The boiler is in a tilted position.  
The switch (A) is “off”.  
Iron thermostat control (J) set  
to the minimum position.  
Faulty power connection.  
Empty boiler  
Place it on a horizontal surface.  
Switch it to “on” (A)  
The iron does not heat and the  
LED (K) does not light up.  
Adjust the thermostat control.  
Check the power points.  
Fill the boiler with water  
Switch them on  
No steam comes out when  
pressing the steam switch (H)  
Leak from the boiler filler cap  
Switches (B) and (A) are “off”  
Cap (F) not properly closed  
Let the boiler cool and screw  
the cap (F) to the end again  
Go to an authorised Technical  
Service Centre  
Safety valve activated  
The boiler cap (F) does not  
unscrew easily  
There is steam remaining inside  
the boiler  
Press the steam switch (H) to  
let the steam out  
 
MW_EX233805 StteamStation_IM.indd  
6
7/25/2007 2:02:51 PM  
 
MW_EX233805 StteamStation_IM.indd  
8
7/25/2007 2:02:51 PM  

Land Pride Lawn Mower HR3584 User Manual
Largan Digital Camera EASY 200 User Manual
Learning Resources Baby Toy LER 6916 User Manual
Learning Resources Games LER 6914 User Manual
LG Electronics Flat Panel Television SAC30708022 User Manual
Linear Stereo Receiver RV5060 User Manual
Lowrance electronic SONAR M68I User Manual
Magic Bullet Blender Magic10 User Manual
Melissa Hair Dryer 635 065 User Manual
Melissa Vacuum Cleaner 640 073 User Manual